Jump to content


Photo

Arduino library for communicating with Modbus slaves over RS232/485 Shield


  • Please log in to reply
1 reply to this topic

#1 kang.yang

kang.yang

    Newbie

  • Members
  • Pip
  • 5 posts

Posted 05 April 2014 - 10:40 AM

Arduino library for communicating with Modbus slaves over RS232/485 Shield

 

Overview

This is an Arduino library for communicating with Modbus slaves over RS232/485 (via RTU protocol). Updated to support Arduino 1.0.

Features

The following Modbus functions have been implemented:

  • 0x01 - Read Coils
  • 0x02 - Read Discrete Inputs
  • 0x05 - Write Single Coil
  • 0x0F - Write Multiple Coils
  • 0x03 - Read Holding Registers
  • 0x04 - Read Input Registers
  • 0x06 - Write Single Register
  • 0x10 - Write Multiple Registers
  • 0x16 - Mask Write Register
  • 0x17 - Read Write Multiple Registers
Uploading Sketches

Arduinos prior to the Mega have one serial port which must be connected to USB (FTDI) for uploading sketches and to the RS232/485 device/network for running sketches. You will need to disconnect pin 0 (RX) while uploading sketches. After a successful upload, you can reconnect pin 0.

Hardware

This library has been tested with an Arduino Duemilanove, PHOENIX CONTACT nanoLine controller, connected via RS485 using a Maxim MAX488EPA transceiver.

Installation

The latest version can be downloaded from Github.

Arduino 17 (or later) Determine the location of your sketchbook by selecting File > Preferences from within the Arduino IDE. If you don't already have a libraries folder within your sketchbook, create one and unzip the archive there. See this for more information. Arduino 16 (or earlier) Download the zip file, extract and copy the ModbusMaster folder to ARDUINO_HOME/hardware/libraries. If you are upgrading from a previous version, be sure to delete ModbusMaster.o. Support

Please report any bugs on the Issue Tracker.

Questions/Feedback

I can be contacted at 4-20ma at wvfans dot net.

Example

The library contains a few sketches that demonstrate use of the ModbusMaster library. You can find these in the examples folder.

/*
Basic.pde - example using ModbusMaster library

This file is part of ModbusMaster.

ModbusMaster is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.

ModbusMaster is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with ModbusMaster. If not, see <http://www.gnu.org/licenses/>.

Written by Doc Walker (Rx)
Copyright © 2009-2012 Doc Walker <4-20ma at wvfans dot net>

*/

#include <ModbusMaster.h>

// instantiate ModbusMaster object as slave ID 2
// defaults to serial port 0 since no port was specified
ModbusMaster node(2);


void setup()
{
// initialize Modbus communication baud rate
node.begin(19200);
}


void loop()
{
static uint32_t i;
uint8_t j, result;
uint16_t data[6];

i++;

// set word 0 of TX to least-significant word of counter (bits 15..0)
node.TX(0, lowWord(i));

// set word 1 of TX to most-significant word of counter (bits 31..16)
node.TX(1, highWord(i));

// slave 1: write TX to (2) 16-bit registers starting at register 0
result = node.WriteMultipleRegisters(0, 2);

// slave 1: read (6) 16-bit registers starting at register 2 to RX
result = node.ReadHoldingRegisters(2, 6);

// do something with data if read is successful
if (result == node.ku8MBSuccess)
{
for (j = 0; j < 6; j++)
{
data[j] = node.RX(j);
}
}
}

Project inspired by Arduino Modbus Master.

 

via http://playground.ar...de/ModbusMaster

 



#2 kang.yang

kang.yang

    Newbie

  • Members
  • Pip
  • 5 posts

Posted 05 April 2014 - 11:53 AM

I try to google arduino-modbus-slave . I find that : https://code.google..../downloads/list

 

maybe helpful for you .






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users