Jump to content
nutzenbolz

snappy ubuntu release

Recommended Posts

Anybody try the new Snappy for pcDuino3? I flashed it, but I can't really tell what's happening other than the lights flashing briefly. I doesn't seem to be running the ethernet over USB-OTG as I get no sign of it in my Windows network settings. I have no HDMI monitor. Has anybody tried installing it and has any feedback about it?

 

Edit - also there is no information about what the file actually is. I'm not sure if it's a bootable SD or a production SD to flash NAND.

Share this post


Link to post
Share on other sites

I tried to get it to work for about 3 hours today.  Takes a long time to burn to SD. No video output but lights on keyboard and mouse look active. No debug output either.

 

I have sent a request for more info. Will update as soon as I know something.

Share this post


Link to post
Share on other sites

I installed it on my nano without too many troubles. Disadvantages are: no headless install possible (had to config the network settings), no x11vnc for remote desktop. Off course x11vnc can be installed using apt-get, but I cannot get x11vnc to run automatically... but that can only be a trivial issue...

Share this post


Link to post
Share on other sites

Problem was not uart connection or snappy OS. It was an SD card that died.

 

Snappy is up and running. However, I have no ethernet connection. pcDuino3A

Trying to find the IP address...

ubuntu@localhost:~$ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 52:5d:3f:79:10:6d brd ff:ff:ff:ff:ff:ff
    inet 10.0.1.49/32 scope global eth0
       valid_lft forever preferred_lft forever
3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default
    link/sit 0.0.0.0 brd 0.0.0.0

I then try to take eth0 down and bring it back up with dhcp.

ubuntu@localhost:~$ sudo ip link set dev eth0 down
ubuntu@localhost:~$ sudo dhclient eth0
[  835.566018] stmmac_hw_setup: DMA engine initialization failed
[  835.571782] stmmac_open: Hw setup failed
RTNETLINK answers: Device or resource busy
ubuntu@localhost:~$ [ 1308.837715] stmmac_hw_setup: DMA engine initialization failed
[ 1308.843473] stmmac_open: Hw setup failed

Share this post


Link to post
Share on other sites

ubuntu@localhost:/media$ sudo dmesg | tail
[ 2592.339548] audit: type=1400 audit(1423121670.580:470): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2606.182655] audit: type=1400 audit(1423121684.430:471): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2606.182901] audit: type=1400 audit(1423121684.430:472): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2606.183047] audit: type=1400 audit(1423121684.430:473): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2620.341690] audit: type=1400 audit(1423121698.590:474): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2620.341933] audit: type=1400 audit(1423121698.590:475): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2620.342092] audit: type=1400 audit(1423121698.590:476): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2631.046927] audit: type=1400 audit(1423121709.290:477): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2631.047163] audit: type=1400 audit(1423121709.290:478): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
[ 2631.047305] audit: type=1400 audit(1423121709.290:479): apparmor="DENIED" operation="sendmsg" profile="/sbin/dhclient" name="/run/systemd/journal/dev-log" pid=796 comm="dhclient" requested_mask="w" denied_mask="w" fsuid=0 ouid=0
ubuntu@localhost:/media$

Share this post


Link to post
Share on other sites

I think Snappy would be a good idea for the pcDuino Lite wifi. Compact and headless should mean lower power needs. Perhaps a compact version with axp209 and battery connector could be used for wireless IoT.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×